SbfI-HF®

Restriction Enzymes SbfI / SdaI

Experiment
Restriction Enzymes SbfI / SdaI
Product
SbfI-HF® from New England BioLabs
Manufacturer
New England BioLabs

Protocol tips

Protocol tips
This assembly was subsequently combined with the leash precursor at a ~130 nM final concentration, each in 1× CutSmart buffer, along with 10 units (U) of SbfI-HF, 10 U of MluI-HF, 10 U of NsiI-HF, 5 U of AscI, 1,000 U of T4 DNA ligase (New England Biolabs), 1 mM ATP and 1 mM DTT (Step a4 in Supplementary Fig. 1). After overnight incubation at 25 °C, the mixture was heat-inactivated at 65 °C for 20 min.

Publication protocol

"Oligonucleotides L1, L2, TS1 and TS2 were synthesized by Trilink and resuspended in formamide (Merck) at 37 °C, so as to obtain a 10 μg μl–1 final concentration. Typically, ~100 μg of each Li was combined with an equimolar amount of the associated TSi and incubated for 12 h at 25 °C to yield the corresponding Ji product by click-chemistry coupling (Step a1 in Supplementary Fig. 1). Both J1 and J2 branched oligonucleotides were then purified by electrophoresis on an 8 M urea and 8% acrylamide/bisacrylamide (29:1) gel, as previously described17. Subsequently, J1 and J2 were used as primers in the PCR amplification of a ~2.0 kbp fragment of the Charomid 9-5 ΔSbfI template with the Expand High Fidelity polymerase system (Roche) (Step a2 in Supplementary Fig. 1)—the template used is a derivative of the Charomid 9-5 plasmid in which the native SbfI site was removed by SbfI digestion, fill-in and ligation with the Quick Blunting kit (New England Biolabs). The resulting branched PCR products, which are the precursors of the tips and shanks of the J-DNA tweezers, were purified using the NucleoSpin Gel and PCR Clean-up kit (Macherey-Nagel).

In parallel, the leash precursor was synthesized as follow. Its ~630 bp backbone was amplified by PCR using the Platinum Pfx DNA polymerase (Invitrogen), the Charomid 9-5 ΔSbfI template and the Charo-3600-MluI and Charo-4230-SbfI primers. The blunt-end PCR product was then digested at one end with SbfI and cloned into the pUC18 vector using the SbfI and SmaI restriction sites. The resulting DNA plasmid, 690_pUC18, was amplified and purified using the NucleoBond Xtra maxiprep kit (Macherey-Nagel), and digested with the MluI and SbfI restriction enzymes. The digestion products were separated using electrophoresis on a 1% agarose gel and extracted using the NucleoSpin Gel and PCR Clean-up kit (Macherey-Nagel).

Next, the L1 and L2 oligonucleotides of the branched PCR product, which did not participate in the amplification reaction, were annealed in an equimolar ratio to the O1-Comp and O2-Comp oligonucleotides, respectively (Step a3 in Supplementary Fig. 1). This reaction took place at a final concentration of ~270 nM in each strand for 1 h at room temperature in 1× CutSmart buffer (New England Biolabs). This assembly was subsequently combined with the leash precursor at a ~130 nM final concentration, each in 1× CutSmart buffer, along with 10 units (U) of SbfI-HF, 10 U of MluI-HF, 10 U of NsiI-HF, 5 U of AscI, 1,000 U of T4 DNA ligase (New England Biolabs), 1 mM ATP and 1 mM DTT (Step a4 in Supplementary Fig. 1). After overnight incubation at 25 °C, the mixture was heat inactivated at 65 °C for 20 min. Then, in a one-pot reaction that took place at 37 °C for 8–16 h, the tips were nicked with 30 U of Nb.BvCI (New England Biolabs) and the extremities of the shanks were digested with 100 U of XbaI and 50 U of SacI (New England Biolabs) (Step a5 in Supplementary Fig. 1). The product was separated on a 1.5% agarose gel at 37 °C and extracted using the NucleoSpin Gel and PCR Clean-up kit (Macherey-Nagel).

Finally, the ~2.7 kbp construct obtained above was ligated at the SacI site to a ~1 kbp dsDNA fragment multiply labelled with biotin and at the XbaI site to a ~1 kbp dsDNA fragment multiply labelled with digoxigenin (Step a6 in Supplementary Fig. 1). These labelled DNA fragments were synthesized by PCR as previously described36,56 in the presence of dUTP-biotin and dUTP-digoxigenin (Roche), respectively. The ligation reaction was conducted for 3 h at room temperature in 10 μl of 1× T4 DNA ligase buffer (New England Biolabs) that contained the construct at 3 nM, biotin and digoxygenin-labelled ~1 kbp fragments at 10 nM each, and 200 U of T4 DNA ligase. The enzyme was then heat inactivated and the resulting J-DNA tweezers were aliquoted and stored at −20 °C."

Full paper   Login or join for free to view the full paper.

Reviews

SbfI-HF® from New England BioLabs has not yet been reviewed for this experiment

We'd love it if you would be the first to write a review!

Discussion

Start your discussion

Share your thoughts or question with experts in your field

Start a discussion

Papers

Check out relevant papers found by Labettor's AI that are relevant for performing Restriction Enzymes SbfI / SdaI using SbfI-HF® from New England BioLabs.

View full paper   Login or join for free to view the full paper.

Manufacturer protocol

Download the product protocol from New England BioLabs for SbfI-HF® below.

We haven't found the manufacturer protocol for this product yet.

Videos

Check out videos that might be relevant for performing Restriction Enzymes SbfI / SdaI using SbfI-HF® from New England BioLabs. Please note that these videos are representative and steps or experiment specific processes must be kept in mind to expect desired results.

We haven't found any additional videos for this experiment / product combination yet.

Outsource your experiment

Fill out your contact details and receive price quotes in your Inbox

  Outsource experiment
Become shareholder Discussions About us Contact Privacy Terms